\nhttp:\/\/www.disk91.com\/2013\/technology\/hardware\/oregon-scientific-sensors-with-raspberry-pi\/
\n
![\"photo(2)\"](\"http:\/\/www.disk91.com\/wp-content\/uploads\/2013\/10\/photo2.jpg\")
<\/p>\nThis:
\nhttp:\/\/shop.ninjablocks.com\/blogs\/how-to\/7506204-adding-433-to-your-raspberry-pi<\/p>\n
and:
\nhttp:\/\/www.disk91.com\/2013\/technology\/hardware\/raspberry-pi-receive-433mhz-radio-signal\/<\/p>\n
if the receiver needs 5v, remember the nice 5v->3.3v circuit:
\nhttp:\/\/www.disk91.com\/2013\/technology\/hardware\/oregon-scientific-sensors-with-raspberry-pi\/
\n<\/p>\n
<\/p>\n
Basically just install wiringPi, then the 433utils:<\/p>\n
root@rpi02:~# git clone git:\/\/github.com\/ninjablocks\/433Utils.git
\nCloning into ‘433Utils’…
\nremote: Counting objects: 129, done.
\nremote: Total 129 (delta 0), reused 0 (delta 0)
\nReceiving objects: 100% (129\/129), 28.02 KiB, done.
\nResolving deltas: 100% (55\/55), done.
\nroot@rpi02:~# cd 433Utils\/RPi_utils
\nroot@rpi02:~\/433Utils\/RPi_utils# make
\ng++\u00a0\u00a0\u00a0 -c -o RCSwitch.o RCSwitch.cpp
\ng++\u00a0\u00a0\u00a0 -c -o send.o send.cpp
\ng++\u00a0\u00a0 RCSwitch.o send.o -o send -lwiringPi
\ng++\u00a0\u00a0\u00a0 -c -o codesend.o codesend.cpp
\ng++\u00a0\u00a0 RCSwitch.o codesend.o -o codesend -lwiringPi
\ng++\u00a0\u00a0\u00a0 -c -o RFSniffer.o RFSniffer.cpp
\ng++\u00a0\u00a0 RCSwitch.o RFSniffer.o -o RFSniffer -lwiringPi
\nroot@rpi02:~\/433Utils\/RPi_utils#<\/p>\n
Then transmit something over 433MHz (car key,\u00a0 electric socket remote control..)<\/p>\n
And run the thing:<\/p>\n
root@rpi02:~\/433Utils\/RPi_utils# .\/RFSniffer<\/p>\n
Try also with the transmitter.<\/p>\n
I can see lights blinking, but RFSniffer doesnt show anything.<\/p>\n
Trying to see what is happening on the pins at lower level with this:
\nhttp:\/\/abyz.co.uk\/rpi\/pigpio\/piscope.html<\/p>\n
pigpiod should be installed first.<\/p>\n
piscope is GREAT!<\/p>\n
<\/p>\n
<\/p>\n","protected":false},"excerpt":{"rendered":"
This: http:\/\/shop.ninjablocks.com\/blogs\/how-to\/7506204-adding-433-to-your-raspberry-pi and: http:\/\/www.disk91.com\/2013\/technology\/hardware\/raspberry-pi-receive-433mhz-radio-signal\/ if the receiver needs 5v, remember the nice 5v->3.3v circuit: http:\/\/www.disk91.com\/2013\/technology\/hardware\/oregon-scientific-sensors-with-raspberry-pi\/ Basically just install wiringPi, then the 433utils: root@rpi02:~# git clone git:\/\/github.com\/ninjablocks\/433Utils.git Cloning into ‘433Utils’… remote: Counting objects: 129, done. remote: Total 129 (delta 0), … Continue reading